焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

基于Stacking的地面PM2.5浓度估算

为了解决地面PM_2.5监测网络在空间和时间覆盖受限的问题,提出了基于宽时空覆盖的卫星气溶胶光学厚度AOD,利用Stacking方法建立地面PM_2.5浓度估算模型,将AOD、PM_2.5和各气象参数以及与PM_2.5排放有关的数据进行训练,使用改进网格搜索对模型超参数进行优化,通过对多重共线性分析,建立基于Stacking的最优PM_2.5浓度估算模型。选取2016-01-01-2016-12-31的数据作为实验对象,结果表明:相比于随机森林、GBRT和XGBoost 3种模型,使用岭回归作为元学习器的Stacking模型性能更优,可见Stacking适用于大范围地理区域的大气污染监测。     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

不同制备温度下污泥生物炭对Cr(Ⅵ)的吸附特性

以城市剩余污泥为原料,于300,400,500,600 ℃温度条件下制备生物炭,通过单因素静态吸附实验探讨制备温度对生物炭吸附Cr（Ⅵ）的影响。结果表明:在500 ℃以内随着温度上升制备的生物炭对Cr（Ⅵ）的吸附量增加,制备温度高于500 ℃后变化不明显;扫描电镜（SEM）、比表面积（BET）、傅里叶红外光谱（FTIR）表征结果显示,热解温度对生物炭表面形貌和官能团组成有显著影响;等温模型及动力学拟合结果表明,生物炭吸附Cr（Ⅵ）为单分子层吸附、物理-化学复合吸附。热解温度对污泥制备生物炭吸附Cr（Ⅵ）的性能有显著影响,最佳制备温度为500 ℃,在此条件制备的生物炭对Cr（Ⅵ）的理论吸附量可达7.93 mg/g。     

污水处理过程专家系统的结构特点与应用研究进展

综述了专家系统在污水处理领域的结构和特点、针对的工艺以及应用现状方面取得的研究成果。重点介绍了专家系统中知识的获取和表示、规则的建立以及与故障树和其他人工智能技术的结合情况,并对专家系统在污水处理工艺选择、运行控制以及故障诊断3个阶段的研究现状进行了细致分析。在此基础上,提出了尚需解决的问题以及进一步研究与发展的方向。     

Concentrations and chemical compositions of PM10 during hazy and non-hazy days in Beijing

In order to study the concentrations of major components,characteristics and comparison in hazy and non-hazy days of PM_(10) in Beijing,aerosol samples were collected at urban site in Beijing from December 29,2014 to January 22,2015.Heavy metals like Zn,Pb,Mn,Cu,As,V,Cr and Cd were deeply studied considering their toxic effects on human being;nine water-soluble inorganic ions(SO_4~(2-),NO_3~-,NH_4~+,Na~+,K~+,Cl~-,Ca~(2+) and Mg~(2+)) and carbon fractions(OC and EC) were also analyzed.The concentrations of heavy metals were 1.03–1.98 times higher in hazy days than those in non-hazy days,mainly due to biomass burning and coal burning.The trends in total heavy metals concentrations were basically consistent with the trends in PM concentrations except for two obvious periods(12.29–12.30;1.14–1.15);but when air masses accumulated locally or around Beijing,trends in PM concentrations and heavy metals were opposite.The proportion for NO_3~-/SO_4~(2-) indicated that mobile sources such as automobiles were important reasons for haze in Beijing.Correlation between OC and EC during non-hazy days was strong(R~2= 0.95) but it was low(R~2= 0.67) during hazy days,and large variations for OC/EC values occurred in hazy days.The calculated mass concentration of SOC is 2.58 μg/m~3,which only accounted for 10.1% of the OC concentration.When air masses from the far north-west,they decreased PM concentration in Beijing and they were relatively clean;however,those from the near east,south-east and south of the mainland increased PM concentration and they were dirty.     

过硫酸钠缓释材料的释放性能及其对2, 4-二硝基甲苯的降解效果

针对原位化学氧化技术修复土壤和地下水时氧化剂因释放过快而导致的利用率低等问题,通过熔化成型法制备过硫酸钠缓释材料,分析石蜡、硅砂和过硫酸钠不同配比对材料成型度和释放性能的影响,研究缓释过程中溶液pH的变化,探讨其在水溶液中的缓释行为及其对2,4-二硝基甲苯（2,4-DNT）的降解效果.结果表明:当固定过硫酸钠质量为6 g、硅砂质量为18 g、蜡砂比（石蜡、硅砂质量之比）为1:4~1:8时,过硫酸钠缓释材料成型度适中,且过硫酸钠的累积缓释量随着时间的延长而逐渐增大,第31天时过硫酸钠累积释放百分比为74.67%~88.40%,可实现过硫酸钠的持续可控释放.当硅砂质量为18 g、蜡砂比为1:1~1:6时,过硫酸钠累积释放百分比随着过硫酸钠质量的增加而增大,且溶液中的pH呈先降低后上升的变化规律.缓释材料缓释前后实物图和显微镜分析结果显示,过硫酸钠缓释材料的释放是一个由外到内、速率由快变慢最终趋于平稳的过程.过硫酸钠质量为12 g、硅砂质量为18 g、蜡砂比为1:4的缓释材料对2,4-DNT具有较好的降解效果,第16次置换浓度为0.2 mg/L的2,4-DNT水溶液时,2,4-DNT的降解率为56.38%.研究显示,改变制备材料的配比可有效实现缓释材料中过硫酸钠的缓慢释放及对污染物的有效降解,可为原位化学氧化修复土壤和地下水提供理论支撑.